Get crystal clear communication in any environment with the MIRA Safety Gas Mask Microphone. It’s engineered to replace the existing exhalation valve cover of your MIRA Safety gas mask, an upgrade that can be installed in seconds without tools. This 2-pin microphone offers integrated noise-canceling functionality with no additional power needed. KEY BENEFITS OF MIRA SAFETY GAS MASK MICROPHONE. Noise-canceling, dynamic, moving-coil microphone in a tough polymer housing. 2-pin NEXUS U-173/U connector for compatibility with Peltor and Ops-Core headsets. Replaces your existing gas mask exhalation valve cover for quick and easy installation (no expert installation needed). Heavy-duty polymer construction with durable retaining ring. Serviceable, with parts available in case of damage. Optimized for all-weather use (-33°C to +77°C) in any environment. Pivoting cable allows for easy ambidextrous alignment. Engineered to meet MIL-STD-461G and MIL-STD-810G. Provides an average of over 30,000 hours of use. IP67-rated for protection against dust, water, and oil. Can be fully submerged in up to 3 feet of water for ½ hour (not recommended). Weighs less than two ounces 2 oz. Made in the Czech Republic. MIRA Safety gas masks come with enhanced speech diaphragms that allow for improved communication over shorter distances. But talking through a gas mask is never easy. Especially if you’re not right next to each other or you’re dealing with any noise, weather, or other distractions. The MIRA Safety Gas Mask Microphone is cross-compatible with all adult-sized MIRA Safety gas masks, making it easy to swap between masks for different types of missions. Installation takes just a few seconds, and you’re ready to connect to your existing communication system. Just like a standard headset, the microphone requires. Additional power, and it has an average life expectancy of 30,000 hours. Gas mask microphones are a relatively minor upgrade that can make a. Difference while using your mask. Communicating via hand signals is difficult in the best situation, and it’s impossible if you’re holding a rifle or riot shield. Having the ability to plug into your existing comms helps you stay better informed and make better decisions when they matter most. GAS MASK MICROPHONE TECHNICAL DATA. Noise cancelling, Dynamic, Moving Coil. Real Output Level (at usual voice level). 3.5mV rms ± 10%. 5% over a bandwidth of 315 Hz to 4000 Hz. Frequency Response (94 dB SPL, 1/1 octave bands). 5 ± 3 dB. 0 ± 3 dB. 2 ± 3 dB. Environmental & Other Data. 1 – Microphone Signal (MIC +). 2 – Microphone Signal (MIC -). 400mm 150O ± 5%. 20 N / 20 S. (-33 to +71) °C. Approved according to PPE directive 89/686/EEC and EMC directive 89/336/EEC. Designed in accordance with MIL-STD-461G. Designed in accordance with MIL-STD-810G. Designed in accordance with CSN EN 140. Ingress Protection (IEC standard 60529). Flame Retardant Properties (UL 94). Mean Time Between Failures (MTBF). 30,000 hours colspan=”2″ rowspan=”1″ data-mce-style=”height: 34px;” style=”box-sizing: border-box; padding: 10px 14px; border: 1px solid rgb(204, 204, 204); height: 34px;”>>30,000 hours. This gas mask microphone is ONLY compatible with MIRA Safety respirators. This includes the CM-6M, CM-7M, CM-8M, and the TAPR. The gas mask microphone is designed to be stored with your CM-6M or CM-7M gas mask. See storage guidance for those masks. This item is in the category “Business & Industrial\Facility Maintenance & Safety\Personal Protective Equipment (PPE)\Masks & Respirators\Other Masks & Respirators”. The seller is “rockmountaintactical” and is located in this country: US. This item can be shipped to United States.
- Model: CM-6M CM-7M CM-8M
- MPN: MIC
- Brand: MIRA Safety
COMBINING PREMIUM FEATURES WITH SUPERIOR MIL-SPEC CONSTRUCTION, MIRA SAFETY’S CM-6M CBRN TACTICAL GAS MASK / FULL-FACE RESPIRATOR PROTECTS YOUR FACE, INTERNAL ORGANS AND RESPIRATORY SYSTEM AGAINST A FULL SPECTRUM OF TOXIC INDUSTRIAL CHEMICALS (TIC) AND CHEMICAL WARFARE AGENTS (CWA) INCLUDING CHEMICAL, BIOLOGICAL AND NUCLEAR THREATS SUCH AS RADIOACTIVE DUST, NOXIOUS GAS, VAPORIZED POLLUTANTS AND MORE. The CM-6M Tactical Gas Mask has a facepiece of tough bromobutyl rubber (CBRN-compliant) for maximum resistance to TIC/CWA contaminants. The full-face respirator’s inner mask is made from a special hypoallergenic compound that ensures excellent tightness and avoids exhaled air contact with the visor to prevent fogging. It also reduces carbon dioxide(CO2) content in the mask’s inner space, which together with its favorable inhalation/exhalation breathing resistance, decreases the physiological burden for the user-providing more comfortable and practical all-day use. The integrated speech diaphragm ensures at least 95% intelligibility of speech, allowing for easy communication with other members of your party. The mask is equipped with a five-point rubber-textile head harness to ensure a snug and lasting fit. The CM-6M CBRN gas mask is produced in one size. To ensure proper functioning, the user’s face must be smooth, free of facial hair, sideburns and other hindrances at the points of contact. The filter is fitted to the mask by screwing to the left or right inhalation chamber. The unused chamber (without filter) is sealed with an inhalation chamber plug. It is necessary to ensure the plug is properly screwed and tightened. Inhalation chambers of the CM-6 mask are ONLY compatible with Rd 40 x 1/7 thread in accordance with the EN 148-1 standard. Selection of a suitable filter depends on the type and concentration of anticipated toxic agent. The CM-6 tactical mask equipped with a TIC or CWA filter is only safe for use in an environment containing at least 19.5% oxygen. The principles of filter selection and application are described in the filter user guides. The CM-6 tactical gas mask may be used in class 1 explosive environments only. The CM-6 mask meets all of the requirements for class 3 of the EN 136 standard. It’s a great choice for riot gear or as a riot control gas mask. The CM-6 tactical gas mask must be stored in a dark, cool and dust-free place free from sudden temperature changes. The storage room should be ventilated regularly. Temperatures may vary between 10°C and 25°C within relative humidity up to 65%. Full face gas masks must not be exposed to radiant heat or sunshine. Fuels, solvents, lubricants and other inflammable substances, including chemicals, must not be stored with masks. Moreover, there must not be any electrical machines or appliances that produce sparks or discharges during operation (ozone creation). Avoid deformation of the rubber parts of the facepiece and internal CBRN gas mask during storage. This item is in the category “Business & Industrial\Facility Maintenance & Safety\Personal Protective Equipment (PPE)\Other Personal Protective Equipment”. The seller is “c.m.e.c.outdoors” and is located in this country: US. This item can be shipped to United States.
- Modified Item: No
- Custom Bundle: No
- Brand: Mira Safety
- UPC: 682670705548
THIS ITEM IS IMMEDIATELY AVAILABLE (only 1 LARGE in stock, BRAND NEW) + FILTER INCLUDED. The CM-7M tactical gas mask is the ultimate chemical, biological, radiological, and nuclear (CBRN) defense system when used in conjunction with suitable filters or breathing apparatus. The military-grade technology used for this full-face respirator provides comprehensive protection against the full spectrum of CBRN agents and toxic industrial chemicals in the form of gases, vapors, and aerosols. The CM-7M CBRN tactical gas mask was designed and developed in cooperation with Czech Army specialists and specifically developed for use with a wide array of optics for advanced tactical capability. The CM-7M hazmat mask meets the EN 136 (Class III) and EN 148-1 standards and is available in three sizes, providing a perfect fit for practically any user. A NATO-standard filter canister can be mounted on either (or both) side of the military mask to make it easier to aim a gun whether right- or left-handed. The material of the face piece (bromobutyl rubber) on this NATO gas mask provides extraordinary protection against all known chemical warfare agents, along with biological, nuclear, radiological, and industrial chemical agents. This tactical gas mask is designed to withstand long-term use in any weather conditions. The inner mask features comfortable hypoallergenic construction that reduces the content of carbon dioxide in the mask and regulates the flow of inhaled air to prevent fogging for more comfortable all-day use. The inhalation chambers on this army gas mask are fitted with the Rd 40 x 1/7 thread in accordance with the EN 148-1 (NATO) standard. This ensures compatibility with the widest range of filters readily available on the market today. These military-grade gas masks are manufactured under the permanent supervision of a representative of the Czech Ministry of Defense and are trusted by military and police users in a wide variety of countries. The lenses of the CM-7M warfare mask are specifically crafted to. Ensure compatibility with all kinds of optical devices while providing a sufficient field of vision. The dual lens configuration provides superior depth perception when compared to a single panoramic faceplate, making it ideal for use with rifle iron sights or in combat. The CM-7M nuclear gas mask is equipped with a drinking system that enables safe drinking in contaminated areas. The drinking system is also compatible with CamelBak hydration systems. Tactical Gas Mask Service Life. The storage and service life of the CM-7M full-face respirator / tactical gas mask is 20 years from the date of production, provided that the recommended storage conditions are observed. Outstanding resistance against all kinds of CBRN agents, industrial toxic gases, riot control gases, etc. High user comfort for superior all-day protection. Easy donning and doffing. Fits up to 2 NATO-standard 40 mm gas mask filters (widely available with a variety of protection levels). Compatible with optical devices night-vision goggles, etc. Allows for safe and easy drinking during use in a contaminated area. Comes with a pre-installed hydration system and canteen. Compatible with CamelBak water bladders with a Type A or M adapter (not included). Sweat drainage through the exhalation chamber. Compatible with helmets and breathing apparatuses. High-quality speech diaphragm enables easy communication with or without communication devices. Binocular Field of Vision: 34%. Effective Field of Vision: 71.5%. Filter Connection Thread: Rd 40×1/7. Resistance Against Penetration of NBC Agents: >48hrs. Inhalation Resistance at 30 L/min: Max. Inhalation Resistance at 95 L/Min: Max. Exhalation Resistance at 30L/Min: Max. Intake of Liquid: 230 ml/min. Functional Reliability: – 30°C up to +70°C. Size1 5.19-5.51inch (small) (for people who weigh 130 lbs or less). Size2 5.51-5.82 inch (medium) (fits 95% of the population). Size3 5.82-6.14inch (large) (for wide faces and people who weigh over 250 lbs). This is a LARGE or SIZE 3 as seen in the ad. Please note ONE filter is INCLUDED. The item “MIRA CM-7M Military Police 40mm thread Gas Chemical Mask Respirator CBRN” is in sale since Tuesday, October 12, 2021. This item is in the category “Collectibles\Militaria\Surplus\Personal, Field Gear\Gas Masks”. The seller is “favreau19″ and is located in Newport Beach, California. This item can be shipped to United States.
- Theme: Militaria
- Country/Region of Manufacture: United States